ISI Certification (BIS) for
Cast Iron or Ductile Iron Drainage Pipes and Pipe Fittings IS 1729 in India
BIS CERTIFICATION FOR CAST IRON OR DUCTILE IRON DRAINAGE PIPES AND PIPE FITTINGS as per IS 1729
1. Introduction to Indian Standard IS 1729; Cast Iron/Ductile Iron Drainage Pipes and Pipe Fittings For Over Ground Non Pressure Pipeline Socket And Spigot Series – Step Bolts for Steel Structures
- IS 1729 cover Cast Iron/Ductile Iron Drainage Pipes and Pipe Fittings for over Ground Non Pressure Pipeline Socket and Spigot Series. This standard specifies the manufacturing, chemical and physical requirements and testing of Cast Iron/Ductile Iron Drainage Pipes and Pipe Fittings for over Ground Non Pressure Pipeline Socket and Spigot Series.
- IS 1729 specifies the quality parameters or characteristics of the Cast Iron/Ductile Iron Drainage Pipes and Pipe Fittings For Over Ground Non Pressure Pipeline Socket And Spigot Series as follows
- Material Test
- Hardness Test
- Casting defects
- Hammer Test
- Leakage Test
- Pipes Dimension mass and Tolerances
- Coating Test
2. Mandate for ISI Mark Certification of Cast Iron/Ductile Iron Drainage Pipes and Pipe Fittings For Over Ground Non Pressure Pipeline Socket And Spigot Series (IS 1729) :
- Under section 14 of Bureau of Indian Standards Act, 1986 (63 of 1986), the Ministry of Commerce and Industry, Department for Promotion of Industry and Internal Trade after consulting the Bureau of Indian Standards has issued the Quality control order.
- As per the Quality control order, all the manufacturers of Cast Iron/Ductile Iron Drainage Pipes and Pipe Fittings for over Ground Non Pressure Pipeline Socket and Spigot Series are obligated to obtain ISI Mark Certification.
3. Types of Malleable cast iron pipe fittings covered under IS
| “Licence is granted to use Standard Mark on Malleable cast iron pipe fittings as per IS 1879:2010”. | |
|---|---|
| Types / Scope of license | Type of Fitting – Elbow, Tees, Crosses, Bends, Sockets….. Grade - Grade BM-300 (as per IS 14329) Size Designation - |
4. Procedure to obtain BIS Certification of Malleable cast iron pipe fittings to use ISI mark as per IS 1879
- For Indian Manufacturers (Standard Timeframe – 30 days) click here
- For Foreign Manufacturers (Standard Timeframe – 180 days)click here
5. Requisites to get the BIS license for Malleable cast iron pipe fittings
- Conformity of Raw Material as per IS 1879
- In-house testing laboratory for mandatory tests
- Competent Quality Control Personnel
- Adherence to the BIS guidelines for Malleable cast iron pipe fittings as per Indian standard IS 1879
- There are 3 major categories of document required to get the BIS license:
- Administrative Details
- Technical Details
- Quality Control Personnel Details
- Commercial Details
6. Expenses involved in obtaining BIS certificate for Malleable cast iron pipe fittings as per IS 1879 under the Product Certification (Scheme-I) of BIS :
| For Indian Manufacturers | ||||
|---|---|---|---|---|
| No. | Major Charges | Amount | Remark | |
| 1. | BIS Fee | Application Fees | INR 1000 | To be paid in BIS A/c directly. 20% rebate on Marking Fee for MSME units. |
| Audit Charges | INR 7000 | |||
| License Fee | INR 1000 | |||
| Marking Fee | INR 71,000 | |||
| 2. | Testing Charges | Sample Test Fee | As Applicable | To be paid into BIS approved Lab A/c |
| 3. | ERCS Service Fee | Consultancy & others | As per actual, (Depending upon the product and the region of factory) | |
| For the Foreign Manufacturers | ||||
|---|---|---|---|---|
| No. | Major Charges | Particulars | Amount | Remark |
| 1. | BIS Fee | Application Fees | USD 30 | To be paid into BIS A/c directly in USD (SWIFT). SAARC countries can pay in INR with GST@18% |
| Audit Charges (consolidated) | USD 3200 to USD 5900 | |||
| License Fee | USD 30 | |||
| Marking Fee | USD 890 | |||
| 2. | Testing Charges | Sample Test Fee | As Applicable | To be paid into BIS approved Lab A/c |
| 3. | ERCS Service Fee | Consultancy & others | As per actual, (Depending upon the product and the region of factory) | |
- In the certification process, product testing is the most important stage as it determines whether the quality of the product meets Indian standards.
- For the same purpose, investments in testing facilities are required to install test equipment for internal factory test laboratories.
- Apart from charges mentioned above in the table, we may ask you to pay/reimbursement for a Pre-Visit at your Factory Premises to ensure the conformity of your product as per the relevant Indian Standard & BIS guidelines for its BIS certification.
7. Role of ERCS Private Limited in getting your product certified:
- To get BIS certification and produce a standard quality product, the manufacturer must ensure that their product must follow the specified Indian Standard Specifications (ISS) which we directly interpret to you from the BIS officials as per the Indian Standards.
- ECRS Private Limited will be your friend, philosopher and guide in the whole process of getting your product certified by the concerned authorities/ departments.
- Scope of work by ECRS Private Limited:
Ensuring the conformity of your product as per IS 1879:
ERCS Pvt. Ltd. has developed a vast network within the Iron Industry & various BIS departments to assist for ensuring conformity of the product Malleable cast iron pipe fittings according to according to IS 1879.
Effective documentation with the awareness of the BIS guidelines:
order to facilitate the manufacturing industry in obtaining BIS certifications, guidelines have been developed. Our team has the experience of completing over 150 projects and technically competent acquaintances in various Industries. We are familiar with the Indian Standard Specifications & BIS guidelines and deliver the most suitable interpretation to the Quality Control Personnel so we can do a reliable and effective documentation of your product in accordance with the BIS guidelines.
A pre-visit can be paid at your factory premises:
In the process of getting BIS certification, the officer from BIS authority visits the factory for inspection. In order to get good results, the BIS inspection should go smoothly without any Non-Conformity. By keeping this goal in mind, our team will organize a pre-visit to your factory premises so that required changes can be adapted so as to remove the elements of fallibility.
Assistance for BIS audits:
We will explain the whole procedure of conducting a BIS inspection and make you aware of the things which need to be prepared and readily available at the time of inspection.
Benefits of getting ISI Mark for Polypropylene (PP) Materials for Moulding and Extrusion to sell in Indian Market with our help
- The term “ISI mark" means, that a certain product conforms to the quality standards set up by the government.
- It is compulsory for Polypropylene (PP) Materials for Moulding and Extrusion to obtain the ISI Mark and the violators are penalized with the material seize and a significant sum as fine.
- Getting certification improves the probability of your product to survive and compete in the market.
- Customers have the tendency of buying ISI certified products as it ensured safety and standard quality. Hence, with the certified products you can win the confidence and trust of the buyer.
- With the word of mouth of such client list, you can establish your credibility in the market.
- Hence with the renowned brand, you can raise the standard and benchmark the market value of the product.