ISI Certification (BIS) for
Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply IS 15633:2022 in India

BIS CERTIFICATION OF AUTOMOTIVE VEHICLES-PNEUMATIC TYRES FOR PASSENGER CAR VEHICLES– DIAGONAL AND RADIAL PLY IS 15633:2022

Radial tyres were developed in 1946. There was a need for more flexible tyres, which were able to absorb shocks generated by road surfaces. These tyres are also stronger, which means machines can be operated at higher capacities. In radial tyres, steel cord plies are placed on the heel of the tyre, and a belt is placed across the casing. Because cord plies are placed directly on top of each other, the side walls of radial tyres remain very flexible. Diagonal tyres have been used instead of solid rubber tyres since 1898. They were a standard feature in the car industry before radial tyres were introduced. Diagonal tyres consist of casing layers made from nylon cord. They are placed diagonally across each other in the tread and the side walls, at an angle of 55 degrees. Diagonal tyres are used, for example, to perform activities in ports, often on reach stackers

Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply is used in the following areas –

• High vehicle stability
• Higher resistance against side wall damage
• Good steering and better road contact
• Little heat generated in tyre at high speeds
• Higher resistance against tread-related damage

Introduction to Indian Standard IS 15633; Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply

• IS 15633 cover Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply. This standard specifies the general, dimensional and performance requirements of new diagonal and radial ply pneumatic tyres designed primarily for vehicles in categories M1, T1 and T2. However, it does not apply to run flat tyres, and tyres designed for:

1. a) The equipment of vintage cars, and
2. b) Competitions (racings)

• IS 15633 specifies the quality parameters or characteristics of the Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply as follows

Tyre Dimensions

Load/ Speed Performance Test

Endurance Test

Bead Unseating Resistance Test for Tubeless Tyres

Tread Wear Indicators

Tyre Strength (Plunger Test)

Marking

Type Approval

For more info on the product standardization click here

Mandate for ISI Mark Certification of Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply (IS 15633) :

• Under section 14 of Bureau of Indian Standards Act, 1986 (63 of 1986), the Ministry of Commerce and Industry, Department for Promotion of Industrial Policy and Promotion(LR Section) after consulting the Bureau of Indian Standards has issued the Pneumatic Tyres and Tubes for Automotive Vehicles  (Quality control) order, 2009
• As per this Quality control order, allthe manufacturers of Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply are obligated to obtain ISI Mark Certification.

Types of Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply covered under IS 15633

Please refer to ANNEX - D

Procedure to obtain BIS Certification of Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply to use ISI mark as per IS 15633

For Indian Manufacturers (Standard Timeframe – 30 days) click here

For Foreign Manufacturers (Standard Timeframe – 180 days)click here

Requisites to get the BIS license for Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply

Conformity of Raw Material as per IS 15633

In-house testing laboratory for mandatory tests

Competent Quality Control Personnel

Adherence to the BIS guidelines for Pneumatic Tyres for Passenger Car Vehicles – Diagonal and Radial Ply as per Indian standard IS 15633

There are 3 major categories of document required to get the BIS license:

Administrative Details

Technical Details

Quality Control Personnel Details 

Commercial Details

Expenses involved in obtaining BIS certificate for Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply as per IS 15633 under the Product Certification (Scheme-I) of BIS :

• In the certification process, product testing is the most important stage as it determines whether the quality of the product meets Indian standards.
• For the same purpose, investments in testing facilities are required to install test equipment for internal factory test laboratories.
• Apart from charges mentioned above in the table, we may ask you to pay/reimbursement for a Pre-Visit at your Factory Premises to ensure the conformity of your product as per the relevant Indian Standard & BIS guidelines for its BIS certification.

Role of ERCS Private Limited in getting your product certified :

• To get BIS certification and produce a standard quality product, the manufacturer must ensure that their product must follow the specified Indian Standard Specifications (ISS) which we directly interpret to you from the BIS officials as per the Indian Standards.
• ECRS Private Limited will be your friend, philosopher and guide in the whole process of getting your product certified by the concerned authorities/ departments.

• Scope of work by ECRS Private Limited:

Ensuring the conformity of your product as per IS 15633:

ERCS Pvt. Ltd. has developed a vast network within the Automobile Accessories Industry & various BIS departments to assist for ensuring conformity of the product Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply according to according to IS 15633.

Effective documentation with the awareness of the BIS guidelines:

In order to facilitate the manufacturing industry in obtaining BIS certifications, guidelines have been developed. Our team has the experience of completing over 150 projects and technically competent acquaintances in various Industries.

We are familiar with the Indian Standard Specifications & BIS guidelines and deliver the most suitable interpretation to the Quality Control Personnel so we can do a reliable and effective documentation of your product in accordance with the BIS guidelines.

A pre-visit can be paid at your factory premises:

In the process of getting BIS certification, the officer from BIS authority visits the factory for inspection. In order to get good results, the BIS inspection should go smoothly without any Non-Conformity. By keeping this goal in mind, our team will organize a pre-visit to your factory premises so that required changes can be adapted so as to remove the elements of fallibility.

Assistance for BIS audits:

We will explain the whole procedure of conducting a BIS inspection and make you aware of the things which need to be prepared and readily available at the time of inspection.

Benefits of getting ISI Mark for Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply to sell in Indian Market with our help

• The term “ISI mark" means, that a certain product conforms to the quality standards set up by the government.
• It is compulsory for Automotive Vehicles-Pneumatic Tyres for Passenger Car Vehicles– Diagonal and Radial Ply to obtain the ISI Mark and the violators are penalized with the material seize and a significant sum as fine.
• Getting certification improves the probability of your product to survive and compete in the market.
• Customers have the tendency of buying ISI certified products as it ensured safety and standard quality. Hence, with the certified products you can win the confidence and trust of the buyer.
• With the word of mouth of such client list, you can establish your credibility in the market.
• Hence with the renowned brand, you can raise the standard and benchmark the market value of the product.